Adhesive tape made from fabric has a tensile strength of not less than 20.41kg/2.54 cm of width. Reduce these quantities to grams and milliliters.
1. Adhesive tape made from fabric has a tensile strength of not less than 20.41kg/2.54 cm of width. Reduce these quantities to grams and milliliters.
Answer:
20.41 kg/2.54 cm = 20410 g/25.4 mm
Step-by-step explanation:
1 kg = 1000 g
[tex]20.41 \times 1000 = 20410[/tex]
1 cm = 10 mm
[tex]2.54 \times 10 = 25.4[/tex]
2. The tensile load in a steel rod is 50,000kg. find the diameter of the rod if the tensile stress is 1400kg/cm2?
Answer:
24cm important to the road
3. what is tensile stress
ANSWERTensile stress is defined as the force per unit area induced in the body in response to externally applied force, which tends to elongate or stretch the body. From: Applications of Nanocomposite Materials in Dentistry, 2019.HOPE IT HELPS
4. Allowable tensile stress on gross area of plate
Answer:
How do you find the gross area of a plate?
Gross section area = Ag = 5 x ½ = 2.5 in2
Net section area (An)
Bolt diameter = db = 7/8 in.
Nominal hole diameter = dh = 7/8 + 1/16 in. ...
Hole diameter for calculating net area = 15/16 + 1/16 in. ...
Net section area = An = (5 – 2 x (1)) x ½ = 1.5 in2
Gross yielding design strength = t Pn = t Fy Ag
i Hope
5. It also known as tensile stress.
Answer:
normal stress or tension
Explanation:
Explanation:
Tensile stress (σ) is the resistance of an object to a force that could tear it apart. It is calculated with the highest tension endured by the object in question without tearing, and is measured in Newtons/mm2, but was originally denoted in tons/inch2. Tensile stress can be defined as the magnitude of force applied along an elastic rod, which is divided by the cross-sectional area of the rod in a direction perpendicular to the applied force. Tensile means the material is under tension and that there are forces acting on it trying to stretch the material.
6. 2. What is tensile strength?
Answer:
shortened to tensile strength (TS), ultimate strength, or {\displaystyle F_{\text{tu}}}{\displaystyle F_{\text{tu}}} within equations,[1][2][3] is the maximum stress that a material can withstand while being stretched or pulled before breaking. In brittle materials the ultimate tensile strength is close to the yield point, whereas in ductile materials the ultimate tensile strength can be higher.#PAKIBRAINLEST
Answer:
Tensile strength, maximum load that a material can support without fracture when being stretched, divided by the original cross-sectional area of the material.
7. When the vessel is in a sagging condition, where does the tensile stress be felt?
Answer:
Longitudinal bending stress would occur if the ship were subjected to ... be a ship with machinery amidships in light condition), is termed as sagging.
PA BRAINLIEST PO,THANKUU <33
8. Refers to the ability of a material to stretch under tensile stress.
Flexibility
Explanation:
Flexibility is an ability to bend an object without breaking or cracking
9. A tensile force pf 500 Newtons acts upon a steel bar 8-mm inlength & 4 mm in width. Calculate the tensile stress in the bar.
Answer:
Letteretetdtdt A sagot
10. equipment tools and a tensile specification used in food processing is important because
Answer:
germs in any surface can pass to you or onother person this is why it is to disinfect the equipment,tools and utensils.
11. A manufacturer claims that the average tensile strength
Answer:
A manufacturer claims that the average tensile strength of thread A exceeds the average tensile strength of thread B by at least 12 kilograms. To test this claim, 50 pieces of each type of thread were tested under similar conditions.
12. This is used where the tap wire is under heavy tensile stress.
Answer:
Answer Plain tap joint
Explanation:
Nothing
Answer:
Knotted Tap
Explanation:
This is used where the tap wire is under heavy tensile stress
Don't worry sa TLE notes ko to
13. is it possible for column to carry a tensile load? Why?
Answer:
In which mode does a column carry a load?
The loads applied to a column are only axial loads. Loads on columns are typically applied at the ends of the member, producing axial compressive stresses. However, on occasion the loads acting on a column can include axial forces, transverse forces, and bending moments (e.g. beam-columns).
14. ___________auniversal tester for materials for testing tensile strength and compressive strength of materials.
Answer:
A universal testing machine (UTM)Explanation:
A universal testing machine (UTM), also known as a universal tester, materials testing machine or materials test frame, is used to test the tensile strength and compressive strength of materials. Clarification: The ability of the material to resist stress without failure is called as strength.15. This is used where tap wire considerable tensile stree circuit
Answer:
Duplex Cross Joint
This is a two-tap wire turned simultaneously and is used where the two tap wire is under heavy tensile stress. ... Western Union Long TieThis is used extensively for outside wiring to extend the length of wire from one end to another
HOPE IT HELPS
#CARRYONLEARNING
16. This is used where the tap wire is under tensile stress.
Answer:
This joint is used where the tapped wire is under heavy tensile stress. ... This is a two tap wire turned simultaneously and is used where the two tapped wire are under heavy tensile stress. Western Union short-tie splice. This is the most widely used splice in interior wiring installation.
Explanation: i hope it helped! :))
17. this is related to the hardness and tensile strength of metallic bonds
Answer:
The hardness of metal is due to strength of the metallic bond . Stronger is the metallic bond ,greater is the hadrness of metal.
Explanation:
18. why is it important to clean and sanitize the tools and u tensils in cooking
Answer:
The objective of cleaning and sanitizing food contact surfaces is to remove food (nutrients) that bacteria need to grow, and to kill those bacteria that are present. It is important that the clean, sanitized equipment and surfaces drain dry and are stored dry so as to prevent bacteria growth.
Answer:To aid in the prevention of microorganisms spreading to food. It's especially crucial to fully wash them after using them with raw food because bacteria can spread to other foods.#CARRYONLEARNING19. It also known as tensile stress. 9 letters _ _ _ _ _ L _ _ _ wrong answer:report
[tex]\huge\bold\color{purple}{♛Answer♛}[/tex]
NORMALTESS OR NORMALSTRESS/TENSIONTensile stress may also be known as normal stress or tension.
#CarryOnLearning!
#Ghoster
20. How did the writer help the readers understand the concept of “tensile strength”?
Answer:
The writer can help readers understand the concept of "tensile strength" by providing a clear definition of the term and explaining its relevance to the topic being discussed.
21. this force are those that a huawei from the center of the structure . letter b. tensile
Answer:
dont know
Explanation:
sayo yaanmodule
22. what is tensile strength? Explain
Answer:
The resistance of a material to breaking under tension.
23. This is used where the top wire is under considerable tensile stress circuit.
Answer:
Plain Tap Joint is the answer
24. In tensile strain, what happens to the diameter of the load when the length increase?
Explanation:
a rose is kind of flowers
25. 3. AKICHEN TENSILS AND EQUIPMENT.
Answer:
KITCHEN utensils AND Equipment are :
1. spatula
2. tongs
3. cutting board
4. whisk
5. grater
6. peeler
7. colander
8. measuring spoon
9. blender
10. ladle knife
11. frying pan
12. measuring cup
13. kitchen knife
14. spoon
15. wooden spoon
Explanation:
sana makatulong salamat
#skeptron correct me if I'M wrong
26. this is used where the tap wire is under considerable tensile stress circuit
Answer:
Duplex cross joint
Explanation:
This is a two-tap wire turned simultaneously and is used where the two-tap wire is under heavy tensile stress.
Answer: Duplex cross joint This is a two-tap wire turned simultaneously and is used where the two tap wire is under heavy tensile stress.
27. a universal tester for materials for testing tensile strength and compressive strength of material
Answer:
A universal testing machine (UTM), also known as a universal tester, materials testing machine or materials test frame, is used to test the tensile strength and compressive strength of materials. An earlier name for a tensile testing machine is a tensometer.
28. why is a tensile strenght a significant property of paper? (explain your anwser)
Answer:
The tensile strength of paper is the maximum stress to break a strip of a paper sheet.
Explanation:
Hope it help
29. The three basic types of stress are tensile, compressive and shearing (pauley, 2012)
Answer:
What is your question?...
30. the tensile strength of weld is expressed in terms of
Answer:
The tensile strength of the weld electrode can be 60, 70, 80, 90, 100, 110, or 120 ksi.
